|
|
Mathematical models of the transformers and asynchronous machines
Cipín, Radoslav ; Běloušek, Josef (referee) ; Patočka, Miroslav (advisor)
The fist part of this work is dealt with the construction of the mathematical models of voltage and current transformers. There are created and simulated models of voltage and current transformer with the nonlinear magnetization characteristics. The second part of this work is dealt with equivalent circuit of the induction motor in the form of Gamma-circuit. The speed-torque characteristic and the dependence of stator current on the slip are calculated from this equivalent circuit. The third part of this work is dealt with electromagnetic design of the alternating current machines by the help of a classic way and a new way.
|
|
|
Modern Mathematical Methods of the Analysis and Synthesis of AC Machines
Cipín, Radoslav ; Skala,, Bohumil (referee) ; Richter, Aleš (referee) ; Patočka, Miroslav (advisor)
The doctoral thesis is divided into three main parts with a focus on induction motors. The first part deals with the electromagnetic design and analysis of windings of AC ma-chines. There is introduced the density of conductors, which describes the distribution of the windings in the slots. There is derived general formula for calculation of the total winding factor applicable to any type of winding. The second part of this work deals with the acceleration method of the induction motors torque-speed characteristics measurement. The measured characteristics are used for exact identification of the equivalent circuit parameters of induction motor. The third section is focused on a very precise identification of the equivalent circuit parameters of induction motor in the form of -circuit. The identification is based on mutual comparison of measured and calculated torque-speed and current-speed characteristics.
|
|
|
Noise suppression of six pole induction machine
Lexa, Jakub ; Janda, Marcel (referee) ; Ondrůšek, Čestmír (advisor)
This thesis deals with noise of electromagnetic origin of six pole three-phases induction machine. Task thesis was rendering literature review. Analysis of the problem consists of various analytical calculations using Matlab and subsequent comparison of results with measured data on real induction machine. The last part of thesis is a summary of conditions for induction machine with low noise.
|
|
|
Analysis and design of the AC machines winding.
Vorel, Luboš ; Huzlík, Rostislav (referee) ; Běloušek, Radim (advisor)
This diploma thesis is focused on an analysis and design of an AC machines windings. In the theoretical part of the thesis, differences between single-layer and double-layer windings are explained. Next, the properties of a stator winding of synchronous machines are described. Finally, the winding factor is determined by means of a standard calculation method and by means of a new progressive calculation method, too. In the experimental part of this thesis, the stator winding of a high-speed synchronous generator excited by permanent magnets on the rotor is designed. This generator is driven by a steam turbine.
|
|
|
Analysis of 1,1 MW permanent magnet synchronous motor
Homolová, Romana ; Cipín, Radoslav (referee) ; Vítek, Ondřej (advisor)
This thesis deals with the elaboration of The Permanent Magnet Synchronous Motor and the calculation of its parameters. In the first part, the construction and used permanent magnets of this motor are listed here. The next part of the thesis contains a short overview of the stator windings, the calculation of the winding factors and calculation of the basic parameters of the stator winding. The calculation of the magnetic induction in the air gap is also illustrated here. The result is recalculated by using the Carter factor and then the value of the first harmonics of air-gap flux density is determined. The result is compared with the analysis in the program FEMM. The next part of the thesis is creating a comprehensive overview of the machine using a replacement circuit diagram and phasor diagrams. Finally, the thesis contains model created in RMxprt and ANSYS Maxwell. The results of the model analysis are compared with the analytical calculation
|
|
|
Analysis of 1,1 MW permanent magnet synchronous motor
Homolová, Romana ; Cipín, Radoslav (referee) ; Vítek, Ondřej (advisor)
This thesis deals with the elaboration of The Permanent Magnet Synchronous Motor and the calculation of its parameters. In the first part, the construction and used permanent magnets of this motor are listed here. The next part of the thesis contains a short overview of the stator windings, the calculation of the winding factors and calculation of the basic parameters of the stator winding. The calculation of the magnetic induction in the air gap is also illustrated here. The result is recalculated by using the Carter factor and then the value of the first harmonics of air-gap flux density is determined. The result is compared with the analysis in the program FEMM. The next part of the thesis is creating a comprehensive overview of the machine using a replacement circuit diagram and phasor diagrams. Finally, the thesis contains model created in RMxprt and ANSYS Maxwell. The results of the model analysis are compared with the analytical calculation
|
|
|
Noise suppression of six pole induction machine
Lexa, Jakub ; Janda, Marcel (referee) ; Ondrůšek, Čestmír (advisor)
This thesis deals with noise of electromagnetic origin of six pole three-phases induction machine. Task thesis was rendering literature review. Analysis of the problem consists of various analytical calculations using Matlab and subsequent comparison of results with measured data on real induction machine. The last part of thesis is a summary of conditions for induction machine with low noise.
|
|
|
Modern Mathematical Methods of the Analysis and Synthesis of AC Machines
Cipín, Radoslav ; Skala,, Bohumil (referee) ; Richter, Aleš (referee) ; Patočka, Miroslav (advisor)
The doctoral thesis is divided into three main parts with a focus on induction motors. The first part deals with the electromagnetic design and analysis of windings of AC ma-chines. There is introduced the density of conductors, which describes the distribution of the windings in the slots. There is derived general formula for calculation of the total winding factor applicable to any type of winding. The second part of this work deals with the acceleration method of the induction motors torque-speed characteristics measurement. The measured characteristics are used for exact identification of the equivalent circuit parameters of induction motor. The third section is focused on a very precise identification of the equivalent circuit parameters of induction motor in the form of -circuit. The identification is based on mutual comparison of measured and calculated torque-speed and current-speed characteristics.
|
|
|
Analysis and design of the AC machines winding.
Vorel, Luboš ; Huzlík, Rostislav (referee) ; Běloušek, Radim (advisor)
This diploma thesis is focused on an analysis and design of an AC machines windings. In the theoretical part of the thesis, differences between single-layer and double-layer windings are explained. Next, the properties of a stator winding of synchronous machines are described. Finally, the winding factor is determined by means of a standard calculation method and by means of a new progressive calculation method, too. In the experimental part of this thesis, the stator winding of a high-speed synchronous generator excited by permanent magnets on the rotor is designed. This generator is driven by a steam turbine.
|
|
|
Mathematical models of the transformers and asynchronous machines
Cipín, Radoslav ; Běloušek, Josef (referee) ; Patočka, Miroslav (advisor)
The fist part of this work is dealt with the construction of the mathematical models of voltage and current transformers. There are created and simulated models of voltage and current transformer with the nonlinear magnetization characteristics. The second part of this work is dealt with equivalent circuit of the induction motor in the form of Gamma-circuit. The speed-torque characteristic and the dependence of stator current on the slip are calculated from this equivalent circuit. The third part of this work is dealt with electromagnetic design of the alternating current machines by the help of a classic way and a new way.
|
guest ::
